Enabled DHCP server on the OPT1 interface and set the IP range. Nothing else touched here. I just configured the general options and hit save. NAT - In the outbound section: Made sure everything was in automatic. Firewall - Added a Pass rule for OPT1 on IPv4 for any IP protocol. Source is OPT1 net and destination is Any. After all of these steps.
OPTIONS_DEFINE= OPT1 OPT2 OPT1_CONFIGURE_ENABLE= test1 test2 OPT2_CONFIGURE_ENABLE= test2=exhaustive. is equivalent to: Seagate/Maxtor has added a user-accessible jumper-switch, known as the "force 150", to enable the drive switch between forced 1.5 Gbit/s and 1.5/3 Gbit/s negotiated operation. Western Digital uses a jumper setting called OPT1 enabled to force 1.5 Gbit/s data transfer speed (OPT1 is enabled by putting the jumper on pins 5 and 6). Jul 01, 2017 · From the "Interfaces" dropdown in the ribbon menu select each VLAN (probably showing as OPT1) and enable them with a static IP address. It is convenient to pick the subnet for the interface that matches the VLAN tag, for example, 192.168.10.1 for the 10 VLAN. Enable DHCP on each VLAN interface in "Services->DHCP Server" Jun 13, 2017 · It helped me get set up and even works with three interfaces (WAN, LAN, and OPT1 for my Wifi router). About the only thing I found missing, and I only mention it because this is a good step-by-step set of instructions to get you going, is to enable pfBlockerNG first, Save, and then go to the DNSBL tab and continue with the instructions. This isn't really recommended, but you can enable access to the GUI from the WAN. If you can, you should: o Do a NAT from a higher port from WAN (e.g. 12345) to LAN 443 o Use a password that meets today's standards o Pin access to the GUI by restricting WAN port access by IPs We do have bugs, but we enjoy fixing them as they come up.
Mar 27, 2012
OPT1 and LAN bridge | Netgate Forum Now go to Firewall > Rules > OPT1 and create a new rule: PASS action, enabled, OPT1 interface, any protocol, source type "OPT1 subnet", any OS, any destination, no log, leave the rest default. Apply. You should now see a PASS rule with all "*"s except for "Source" which should be "OPT1 subnet".
This isn't really recommended, but you can enable access to the GUI from the WAN. If you can, you should: o Do a NAT from a higher port from WAN (e.g. 12345) to LAN 443 o Use a password that meets today's standards o Pin access to the GUI by restricting WAN port access by IPs We do have bugs, but we enjoy fixing them as they come up.
Apr 19, 2020 · I assigned the LAN interface to 192.168.0.1 and OPT1 to 192.168.0.10. After I configured the firewall rules to allow access to the WebGUI on OPT1/ 192.168.0.10, I connected the cable to OPT1 and I could open the WebGUI. Then a strange thing happened when I removed the LAN cable, I could no longer access anything on the OPT1 address. Jan 20, 2018 · Interfaces > OPT1. Make sure OPT1 is enabled. Save and Apply changes. Next we’ll create the bridge but with only OPT1 in there to start. Interfaces > (assign) > Bridges Click Add. And only assign OPT1 first and Save. Interfaces > (assign) Now change LAN from the current assignment to BRIDGE0. This will effectively remove your access. May 03, 2017 · First, assign and enable all the additional interfaces such as opt1, opt2 and so on by visiting Interfaces > (assign) option: Fig.01: Assign network ports Click on each interface name such as opt1, opt2, opt3 and select “ Enable Interface “.